Tutorials

New approach in designing and modelling an Oil pump using Inventor 2016

67 10 Intermediate
Step by step tutorial videos, showing the easy way of modelling an Oil pump using Inventor 2016, how to create the parts, assemble them and drive gears, new approach make use of most Inventor specs, design center with some new tips & tricks ...

LEGO - 01 Basic Dimensions & Bricks Explained

55 7 Intermediate
I get a lot of questions about how I create LEGO parts. This is Part I - The Basics. Most "standard" parts can be created using only simple math. Standard parts consist of square, circular, and angled blocks - regular geometric blocks. I will refer to BrickLink (www.bricklink.com/), but many others use similar methods: Peeron: http://www.peeron.com/ BrickOwl: http://www.brickowl.com/ Brickipedia: http://lego.wikia.com/wiki/LEGO_Wiki etc.

How to model a Centrifugal Pump Body (Spiral construction) using Inventor 2014?

55 17 Intermediate
We have to abide by all the conditions from the technical drawing Note: You can watch my live tutorial for modeling this part here: https://youtu.be/yxEAv2p31zw

LEGO - 02 Building Bricks with Parameters

29 5 Intermediate
I don't get asked this but it is a very powerful tool and will make your life a lot easier. This also applies to other repetitive parts, not just LEGO bricks, and can be applied with the exact same methods.

[VIDEO] Bending Plate Animation Inventor 2020 Tutorial

25 0 Intermediate
This tutorial will show how to create a bending process of a plate in animation, hope this video will give you clear explanation. please leave comment below

Modelling of Impeller

24 4 Beginner
Modelling of Impeller

Inventor 2019 Crash Course for Complete Beginner

23 6 Beginner
Still spending so much time, struggling with learning Inventor on your own? You can stop now! Get a detailed explanation of every single tool. This is the first of a series, and I'll like you to check below to know what to expect in this volume. In this Tutorial, I shall introduce briefly the Inventor 2019 interface, demonstrate how to access the inventor self-help learners path, demonstrate the way to set up the software with your desired Unit style, and then put in my best to handle every single sketch tool in detail.

How to create a Square to Round (Autodesk Inventor)

18 5 Beginner
This tutorial will run you through the process to create a sheet metal square to round from start to finish. Including flat pattern.

Creating a pipe that bends in multiple directions at once in Autodesk Inventor

14 0 Intermediate
Creating a pipe that bends in multiple directions, with the use of 3D sketch

'Tutorial: How to create adaptive springs in Autodesk Inventor'

13 0 Beginner
http://grabcad.com/library/autodesk-inventor-adaptive-spring-tutorial-1

woodwork for inventor and freeform skeleton tutorial

12 2 Beginner
How to model freeform skeleton body to generate sun chair ribs

[VIDEO]Universal Joint

11 6 Beginner
Universal Joint design which consists of several design parts such as; Main Shaft, Connector shaft, Spider, Bearing. In making this design using several features, among others: ~ 2D Sketch ~ Extrude ~ Circular Pattern ~ Fillet/Chamfer ~ Assembly Feature ~ Shell ~ etc.

Inventor 2021 | Radial Engine | Assembly 9

11 3 Beginner
In this video, I demonstrated the assembly of the cylinders and pistons with the crank case used in a typical radial engine. Video demonstrations to the parts used, can be found on my youtube channel linked in my profile. Happy Modeling!

Simple modeling routine demonstration #1

11 1 Beginner
Simple modeling routine demonstration #1 Hinge

IMPELLER IN AUTODESK INVETOR | AUTODESK INVENTOR TUTORIAL | 3D MODELING

10 1 Beginner
INVENTOR