Tutorials

  • stress ×
Small

How to do a static stress analysis in Fusin 360

2 2 Beginner
In this tutorial I will do a simple static stress analysis of a bolt. I will compare the result with my analytic value.
Small

Tutorial 79: Stress Analysis of Composite T-beam

2 0 Intermediate
Composite fracture occurs at three modes, depending on three loading scenarios. Mode I is an opening or tensile mode, mode II fractures consist of a sliding or shear effect and mode III fractures occur due to a tearing or shear loading effect. This report will only be looking at fracture modes of type I and II. In practical occurrences of material fracture caused by cracking, especially in metals, mode I type of fracture is predominantly present. Agenda:  Set up properties for delaminating interfaces inside engineering data  define delaminating interfaces inside ACP  Use predefined interfaces from ACP inside Mechanical  Alternatively use contact definitions with cohesive zone material inside Mechanical  Boundary conditions and analysis settings  Postprocessing
Small

Tutorial 78: Stress Analysis of Composite T-beam

2 0 Intermediate
ACP has a pre- and post-processing mode. In the pre-processing mode, all composite definitions can be created and are mapped to the geometry (FE mesh). These composite definitions are transferred to the FE model and the solver input file. In the post-processing mode, after a completed solution and the import of the result file(s), post-processing results (failure, safety, strains and stresses) can be evaluated and visualized. After a completed solution, the post-processing is used to evaluate the performance of the design and laminate. The post-processing functionality for Solid Models of ACP allows the mapping of ply wise results on to the reference surface of the solid model. This ensures that also failures occurring inside the laminate can be observed and investigated. Failure criteria are used to evaluate the strength of a composite structure. Several failure criteria can be defined, combined and configured in the Definitions object. Failure criteria definitions can be used for failure plots and sampling points. The critical failure mode for an element shown in failure plots and sampling points is the one with the lowest reserve factor. Agenda  Connecting ACP to Static Structural Tools in Ansys  Doing Stress Analysis  Solving the model  Analyzing Data in static Sturcutal  Analyzing Data in Post-Processing
Small

Tutorial 76: Stress Analysis of Composite Pressure Vessel (Solid modeling)

3 1 Intermediate
Meshes can be imported into Mechanical from multiple systems. It is possible to combine composite shell, composite solid, and non-layered shell and solid meshes to perform mixed analysis. Mechanical does not allow overlap of node/element number from multiple systems; therefore, the import fails if the meshes from different systems are overlapping in node/element numbers. Meshes from upstream to downstream Mechanical Models are renumbered automatically to avoid any overlap. For every analysis system (mesh), you have the choice between automatic renumbering (default) and manual configuration. If automatic renumbering is disabled, you must ensure that the element/node numbering is unique for each mesh. In this tutorial, first we will model Composite pressure vessel in ACP then we will model metal parts in mechanical model and at the we will combine models in static structural. Agenda:  Solid modeling of composite vessel  Add metal parts  Transfer parts to ANSYS Mechanical  Apply boundary conditions, loads and solve the model  Evaluate solid model results in ANSYS Composite PrepPost
Missing_small

Tutorial SolidWorks Simulation: Combined Loading

0 1 Beginner
SolidWorks Simulation Tutorial: Combined Loading
Small

Tutorial: How to analyze a distributed force in Catia V5 FEM Analysis

0 0 Beginner
Download the file: Tutorial_FEM_plate.CATPart
Small

Tutorial: How to analyze a thermal load in Catia V5 FEM Analysis

0 0 Beginner
Download the files: Tutorial_FEM_piston.CATPart temperature.xlsx
Small

Solid Edge Tutorial for Beginners - Simple Simulation

0 0 Beginner
-Tutorial-
Small

Tutorial - Analysis of Bracket in ANSYS Workbench?

0 0 Beginner
Here is the tutorial.
Small

Tutorial - Stress Analysis in ALGOR?

0 0 Beginner
Here I am going to show how to apply pressure to a surface. we are going to use the same model.
Small

Tutorial - Stress Analysis in ALGOR?

0 0 Beginner
Here is the tutorial. Since the model used is created in AutoDesk inventor we will not have any problem using it in ALGOR.
Small

Tutorial - Analyzing the rod for von-mises stress using Mechanica in Creo Elements/Pro?

0 0 Beginner
Here is the tutorial.
Small

Tutorial - Using SimulationXpress in SolidWorks for analyzing a rod?

1 0 Beginner
Here is the Tutorial.