Tutorials

Small

CATIA V5 CoverPump - Exercise - 2D into 3D Modeling

1 0 Beginner
In this guide are displayed CATIA V5 steps modeling based on technical drawings 2D into 3D modeling. The 2D drawing is cover pump.
Small

Autodesk INVENTOR - Exercise - 2D into 3D Modeling

0 0 Beginner
In this guide are displayed ADESK INVENTOR steps modeling based on technical drawings 2D into 3D modeling. The 2D drawing is cover pump. Example of exercise/Part Design training. Basic features: Boss-Extrude, Shell, Mirror, Hole, Hole with thread, Circular Pattern, Rectangular Pattern, Fillet. Basic entities of the sketches: Line, Circle, Rectangle Fillet. Reference elements: Offset plane.
Small

SolidWorks - Exercise - 2D into 3D Modeling - Extrude - Shall - Hole with thread - Fillet

1 0 Beginner
In this guide are displayed SolidWorks steps modeling based on technical drawings 2D into 3D modeling. The 2D drawing is pump cover. Example of exercise/Part Design training. Basic features: Boss-Extrude, Shell, Mirror, Hole, Hole with thread, Circular Pattern, Rectangular Pattern, Fillet. Basic entities of the sketches: Line, Circle, Rectangle Fillet. Reference elements: Offset plane.
Small

Extruded boss on the sphere - ADESK INVENTOR - Exercise - 2D into 3D Modeling

0 0 Beginner
In this guide are displayed ADESK INVENTOR steps that are required for extruded boss to the sphere surface and modeling of the overall model based on technical drawings. 2D into 3D solid modeling. Example of exercise.
Small

SolidWorks - 2D into 3D Modeling

0 0 Beginner
In this guide are displayed SolidWorks steps modeling based on technical drawings 2D into 3D modeling. Example of exercise/Part Design training. Basic features: Revolve, Mirror, Hole, Hole with thread, Fillet. Basic entities of the sketches: Line, Circle, Arc, Rectangle Fillet.
Small

SolidWorks - 2D into 3D Modeling

0 1 Beginner
In this guide are displayed SolidWorks steps modeling based on technical drawings 2D into 3D modeling. Example of exercise/Part Design training. Basic features: Boss-Extrude, Cut-Extrude, Mirror, Hole, Hole with thread, Circular Patern, Rectangular Pattern, Fillet. Basic entities of the sketches: Line, Circle, Arc, Rectangle Fillet. Reference elements: Offset plane.
Small

Tutorial 83: Creating Sandwich Composite Plate with Honeycomb Core

3 0 Expert
Honeycomb structures are natural or man-made structures that have the geometry of a honeycomb to allow the minimization of the amount of used material to reach minimal weight and minimal material cost. The geometry of honeycomb structures can vary widely but the common feature of all such structures is an array of hollow cells formed between thin vertical walls. In this tutorial we are going to create sandwich composite plate. First, we will create two composite plates in two different ACP and then we will create honeycomb in mechanical model by using Honeycombcreator extension. Then, we will combine three models into static structural to do stress analysis. At the end we will do eigenvalue simulation. Agenda:  Using two ACP to create two composite plates  Creating Honeycomb by using honeycomb creator  Apply boundary conditions, loads and solve the model
Small

Tutorial 82: Natural Frequencies and Mode Shape of Composite Plate with Hole

1 0 Intermediate
The modal analysis technique is used to determine the vibration characteristics (I,e, Natural frequencies and mode shapes) of linear elastic structures. Our goal is to determine the first 10 natural frequencies and mode shapes for the plate with the hole shown. In this tutorial, first we are going to model simple plate with hole in ACP tools then we are importing model into modal. In the next step, we will have short introduction to modal tools in ANSYS software and do simulation to find natural frequencies and mode shape of composite model. Agenda:  Creating Plate with Hole in ACP  Importing ACP model into modal analysis  Applying boundary conditions  Finding mode shapes
Small

Tutorial 81: Reinforced Beam with Combination of Steel and Composite Material

4 0 Expert
Reinforced Concrete is a common building material for construction of facilities and structures. While concrete has high compressive strength, it has limited tensile strength. To overcome these tensile limitations, reinforcing bars are used in the tension side of concrete structures. In this tutorial, first we are going to model concreate geometry in mechanical model then we need to model 4 structural steel rebar in another mechanical model. at the end we are going to reinforced structural steel rebar by using 4 composite layers Agenda:  Creating all models in CAD software  Using three different type of materials  Connecting two mechanical models and ACP into static structural  Applying boundary conditions, loads and solve the model  Applying variable pressure on beam
Missing_small

Tutorial 73: Simulate Nonlinear Buckling Analysis of a Half-Symmetry Rectangular Beam with ls-dyna

3 1 Expert
Simulate Nonlinear Buckling Analysis of a Half-Symmetry Rectangular Beam with ls-dyna
Missing_small

Tutorial 72: Modeling and testing single lap joint made with composite material by using contact debonding

2 1 Beginner
Modeling and testing single lap joint made with composite material by using contact debonding
Missing_small

Tutorial 40: How to make Buckling test sample with GFRP

0 0 Intermediate
Please check my Youtube channel for a tutorial: https://www.youtube.com/watch?v=Kold-qRGho8
Missing_small

Tutorial 28: Composite Buckling simulation with Ansys Workbench

0 0 Intermediate
HI
Missing_small

Tutorial 27: Composite Buckling simulation with Ansys APDL

0 0 Intermediate
HI
Small

tutorial 9 ( how to make real pool in 3dmax with mental ray render )

1 2 Intermediate
hi https://grabcad.com/library/swimming-pool-2
Small

Tutorial : Essentials Drawing with inventor pro part 1

0 0 Intermediate
Tutorial : Essentials Drawing with inventor pro part 1
Small

tutorial : how render toon with showcase pro ?

0 0 Intermediate
render toon with showcase pro
Small

Tutorial : how to render with showcase pro

0 0 Intermediate
Tutorial : how to render with showcase pro
Missing_small

Tutorial: How to create a Tee with Ribs in SolidWorks 2013? HD

0 0 Intermediate
Tutorial: How to create a Tee with Ribs in SolidWorks 2013,, HD
Small

Tutorial - Modeling square Head bolt with square Nut in SolidWorks?

0 0 Beginner
Here is the tutorial.
Small

Tutorial how to cut body with surface in SW

0 0 Beginner
Tutorial: How to cut bodies with surface
Small

Tutorial - Using cut with surface feature in SolidWorks?

0 0 Beginner
Here is the tutorial.