Learn about the GrabCAD Platform
Get to know GrabCAD as an open software platform for Additive Manufacturing
Visit our new homepage
Home
Control
Shop
Streamline Pro
Partner Program
Print
Community
Inicie sesión
Library
Challenges
Groups
Questions
Tutorials
Engineers
Blog
Inicie sesión
Ashwin Sira
I Do Things
Follow
22
followers
United States
Models
About
Models
17
Tutorials
0
More
Followers
22
Following
0
Likes
132
Following
0
Followers
22
Likes
132
Models
Sort by:
Recent
Recent
Popular
Most liked
Most commented
Most downloaded
Router Corner Rounding Guide
Simple 3D printable corner rounding guide for use with a router and a flush trimming bit. Radius of corner can be customized. Arms should be made l...
4
61
0
Dual Rotor Cycloidal Gearbox
A simple cycloidal gearbox. This unit has two opposed rotors, resulting in much smoother operation at higher speed. It has a 10:1 ratio. More usef...
19
620
0
Cycoidal Gearbox Test
A simple cycloidal gearbox I made as an initial concept. This gearbox has a 30:1 ratio. It works reasonably well. More useful as a simple demonstra...
15
278
1
Simple Component Storage Drawers
I came up with these drawers as a quick storage solution. I made mine simpler than this design, without the finger hole, and divider slots in the d...
21
360
2
Electric Motor Mechanical Load Tester
This is a system I designed for simple mechanical load testing of electric motors. The polycarbonate side panels are loosely fit to enable fast ac...
18
297
0
Underwater Camera Housing With Tilt for F100 Widecam
I designed this housing to be a simple low cost plastic enclosure for an off the shelf webcam to mount on an ROV. I've included the solidworks asse...
35
689
4
Headway 38120 10 Ah Cell
Model of a Headway 10Ah LiFePO4 cell I made. Has M6 female threads in the terminals. Multiple cells of varying capacity have the same form factor
9
439
0
Norco Ignite Mountain Bike
A mockup of a Norco Ignite I came up with for a project. The frame is fairly accurate. The rest of the parts were mocked up for general dimensions ...
2
71
0
Luna Cycle Cyclone 3kW Brushless Motor with Mounts Mockup
This is a mockup of a 3kW motor kit I made for virtually testing fitment for an eBike project. The kit is the Cyclone 3kW Mid Drive kit with a plan...
23
361
0
Underwater Camera Housing
Camera housing I designed and had built as a part of a robotics project, meant to mount on an AUV. It was built to fit the compact Point Grey Black...
81
1378
8
Cable Penetrator Housing 1/2-20in Thread
Penetrator housing I designed as a part of a university robotics project to pot arbitrary cables through. 3/8in bore diameter to pass cables though...
10
185
0
Red ROV
Model of an ROV from a university project. The frame and housings were being discarded by a research lab, and they donated it. The flat bottom plat...
36
545
1
ROV Frame
Model of an ROV frame found at my university. Some mounting holes were omitted, but the major parts are there. The robot was run in RoboSub many ye...
4
111
0
Aquastar 120A Boat ESC
Rough mockup of a 120A Turnigy Aquastar boat ESC.
3
55
0
RJ45 Ethernet Plug Mockup
Rough model of an RJ45 plug
5
896
0
Widecam F100 Mockup
Mockup of the Genius Widecam F100 I made without the base stand or mounts. Solidworks file was made by an educational copy.
3
201
1
L-FAT A Battery
Simple model of a Panasonic HHR-450AB21 NiMH rechargable battery.
4
87
0
