Learn about the GrabCAD Platform
Get to know GrabCAD as an open software platform for Additive Manufacturing
Visit our new homepage
Home
Control
Shop
Streamline Pro
Partner Program
Print
Community
Log in
Library
Challenges
Groups
Questions
Tutorials
Engineers
Blog
Log in
Davis Woody
Prototype Development Engineer
Follow
Hire me
415
followers
Chattanooga, United States
Models
About
Models
48
Tutorials
0
More
Followers
415
Following
108
Likes
224
Following
108
Followers
415
Likes
224
Models
Sort by:
Recent
Recent
Popular
Most liked
Most commented
Most downloaded
Walksnail Avatar GT VTX
The Caddx Walksnail Avatar GT is a 2W digital VTX. This is a WIP but this model is relatively dimensionaly accurate for any mock-ups you may need t...
12
251
2
HY2+8Y Multi Connector Panel Mount 30A/5A 500VDC
This is a HY2+8 pin multi connector. The big pins are rated for 30A continuous or 60A peak, while the small pins are rated for 5A continuous 7A pea...
8
67
0
JY6P 6 Pin Multi Connector Panel Mount 5A 500VDC
This is a JY6P 6 pin multi connector. It is rated for 5A continuous or 10A peak. It can be used for many things, including RC plane servo, control,...
7
75
0
Top Speed Quadcopter V4 Frame
This is the frame from my V4 top speed drone. I plan to release the full model once my top speed run is completed. The frame is CNC cut and assemb...
100
844
9
CNC 4th Axis using Harmonic Drive and Angle Plates
This is a low cost (~$600) DIY 4th axis design which maximizes precision by using off the shelf precision ground cast iron angle plates. Cast iron ...
80
696
0
ACER 1440G Lathe Half Nut
This is a 1:1 copy of a new replacement component for my machine. The thread is some type of 1" 4TPI ACME but is not to any specification I could f...
8
26
0
ACER 1440G Lathe Power Feed Worm Gear Retainer (Upgrade)
This is the stock retainer but widened for a brass washer on either side of the worm.
11
36
0
APC 7 x 11E 7" Propeller Recreation from Optical Scan
This is the APC 7 x 11E propeller. This model was created from a 0.2mm resolution optical scan mesh.
63
2074
9
Enclosed Micro Ball Gimbal Camera (2x Visible + Thermal) Concept
This is a concept that I have been working with since late last year. The idea is to use 2x Arducam cameras (one wide angle and one telephoto) on a...
147
1208
10
APC 8 x 8E 8" Propeller Recreation from Optical Scan
This is the APC 8 x 8E propeller. This model was created from a 0.2mm resolution optical scan mesh. This small propeller has a very high pitch (u...
74
1985
8
APC 5.25 x 8E 5" Propeller Recreation from Optical Scan
This is the APC 5.25 x 8E propeller. This model was created from a 0.2mm resolution optical scan mesh. This small propeller has a very high pitch ...
44
938
2
MATEKSYS H743 SLIM V3 Flight Controller
FC Specifications MCU: STM32H743VIH6, 480MHz , 1MB RAM, 2MB Flash Board V1.0 IMU: MPU6000 (SPI1) & ICM20602 (SPI4) Board V1.5 IMU:...
37
1018
1
BrotherHobby Avenger 2510 1380kV Motor
Remix of https://grabcad.com/library/brotherhobby-avenger-2806-5-1300kv-motor-1
23
300
0
MATEK FCHUB 12S VS PDB (Power Distribution Board + Voltage Regulation)
This was modeled from reference photos, so please do not consider this dimensionally accurate. With that said, this model should be fairly accurate...
41
1025
2
FLYCOLOR X-CROSS 60A HV 5-12S ESC
This was modeled from reference photos, so please do not consider this dimensionally accurate. The width and length should be fairly accurate, but ...
24
365
3
BETAFPV 2-3S 20A AIO FC V1.0
This is an All In One FC/ESC/RX unit from BETAFPV. Props to Riley Entropy since I stole some of the board parts from her.
25
248
0
MultiGP 3" 3S Micro Toothpick Racing Drone - The Sanchez Build
Frame: The Sanchez by Dave_C_FPV https://www.thingiverse.com/thing:3647138 FC: BetaFPV F4 2-3S 20A AIO FC V1 (original model) VTX/Camera: Walksna...
60
569
2
7deg More Tilt Canopy for Flywoo Nano Baby 20 2S Avatar HD
Feel the need for more speed? This is a 26.7° tilt canopy without RunCam mount for the Flywoo Nano Baby 20 2S Avatar HD. Recommended to print in TPU.
14
75
1
Kurt DX6 Machine Vice Screw Channel Cover
This design prevents chips from falling into the screw channel of the vice. The design has a spot for a 1/2" x 1/8" magnet, and a hole which can be...
10
108
0
Rat Rig V-Core 3.1 Enclosed IDEX Beta 0.5 Wide Boy With Rat Rig Toolhead and Stand
This is my personal 3D printer. This model is a WIP. -Rat Rig IDEX 300 IDEX Beta 0.5 Wide Boy -Rat Rig Toolhead -Sherpa Micro -Lighting strips
18
164
0
Flywoo Nano Baby 20 2S Avatar HD Micro Quadcopter *2 Duct Options*
This is a reference model of the Flywoo Nano Baby 20. **If you use my ducts, make sure you print the mounts in the correct orientation** The proto...
26
203
0
Shen Drones Squirt V2 3" Cinewhoop with beefier base plate
I broke my frame so I redesigned it to be more robust. This adds only around 3 grams to the frame. Dual 20x20 mounting holes modified for GOKU HD ...
23
194
0
HGLRC M100 Mini GPS
Reference model of https://www.hglrc.com/products/hglrc-m100_mini-gps
10
251
0
Facial Interface for Caddx Walksnail Avatar Goggles X
This is a 3d printable (TPU) facial interface for the Goggles X meant to make the goggles more comfortable for more angular faces. I included the ...
19
161
0
1
2
