Learn about the GrabCAD Platform
Get to know GrabCAD as an open software platform for Additive Manufacturing
Visit our new homepage
Home
Control
Shop
Streamline Pro
Partner Program
Print
Community
Log in
Library
Challenges
Groups
Questions
Tutorials
Engineers
Blog
Log in
Kenneth
Follow
Hire me
8
followers
Norway
Models
About
Models
19
Tutorials
0
More
Followers
8
Following
1
Likes
32
Following
1
Followers
8
Likes
32
Models
Sort by:
Most downloaded
Recent
Popular
Most liked
Most commented
Most downloaded
BMG Extruder for MK3S V2
New version with only one led light. The cable managment for dual light was a bit to much, and the placement for the light was not perfect. So it w...
26
431
2
Bondtech for Prusa MK3/S
Drop-in extruder for Bondtech. No change of firmware, but you need to change e-step for the 3:1 ratio in the BMG. This is tested on my MK3S and wor...
25
386
6
Spindle Z axis mount for Xcarve
Made a new design for the Z axis so I could mount a water cooled chinese spindle on my Xcarve 750. Using MGN rails and redesigned the motor mount t...
43
269
9
Prusa MK3S Linear rail with BMG
I made this because I did not have enough rods to build a new MK3s from scratch, so I designed it with MGN9 instead since I had that. I converted t...
33
242
7
Bondtech BMG for Prusa MK3S
Cooling from the back with 4021 fan. I got no heat creap with this design and use it with my Palette 2s Pro + Prusa MK3S. No need for custom firmwa...
18
194
3
Spindle mount and Z axis 0.8KW Xcarve
New Z axis with spindle mount for 0.8KW water cooled spindle 65mm. Get the spindle close as possible to the X gantry.
16
161
1
Potentiometer on/off double
These are usually on the chinese amplifiers from Aliexpress. I needed to fit 3dprinted parts to one so I made this by measure one.
2
111
0
Goofoo Nova Hemera mount with Vulcan
I wanted Hemera with Vulcan on my Goofoo Nova, so I designed this from scratch using measuring everything on my Nova. MGN is imported from Hiwin bu...
8
76
0
COVID-19 Shield Plastic fastener
Share the clip used for one of the face shield if anyone need to edit.
3
52
0
Covid-19 Shield
Based on the Prusa model, but for ordinary strap and clip on instead of punch holes
3
43
0
GooFoo Nova Mutant V2 mount
You need to remove 4 sections of the cable chain for this upgrade. For the sensor I replaced it with this. It is same wire connection and even th...
15
38
1
Insta360 EVO
Model of the Insta360 Evo camera. I have not made joints, but I split it in different components and should be easy to adjust if needed. Good mode...
0
30
0
4x5 Single sheet holder
I made this single sided for 3d printing. I have printed it and seems ok, but not tested it. I just share it here, so others could try it. Please c...
2
25
0
4x5 Ground glass
Measured after Canham DLC 4x5. 2mm thick and grid.
0
24
0
4x5 Single sheet holder
It might not be 100% done, but it is a good start.
0
20
0
Covid-19 FaceShield with clip
Version with holes and hole clip. Should be possible for stacking
1
19
0
Sample model to present 3dprinter filament
Fillamentum have a great sample model to present the color and transparency of the filament. The thinnest layer is 0.3mm thick and show how transpa...
1
16
0
Sidepanels Raise3d E2
If you take out the “bucket” on the side of Raise3d E2 where you usually have the filament spool you could place these panels instead and mount the...
0
16
0
Covid-19 LightWeightShield
A light weigh mount for shield that got punch holes for 4 hole punch.
0
13
0
