Tutorials

  • Drafting ×
  • CFD ×
  • Process Simulation ×
  • Process ×

Cap screws and machine screws

dea
in Drafting
69 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.
Autodesk Inventor screw cap

I Built a Military Robot

Engineering Juice
in Process
46 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

How to Prepare Your 3D Model for Manufacture

Russell Everard
in Process
32 1 Expert
Using this ladies bike model found in the thousands of models available on GrabCAD I have made a step-by-step guide on how to break down your top level assembly for the workshop or for outsourcing.
SOLIDWORKS cutting laser fabrication cnc fixings assemblies manufacture solidworks

Solidworks Tutorial # 236 How to Design a Industrials Bin in Sheet Metal by SW Easy Design

Praveen Kumar
in Drafting
24 0 Intermediate
M.K. Engineering Workshop GST : 09BETPM3972F1ZW Please any Manufacturing requirement in Rice Mill, Floor Mill, Dall Mill, any Related Product. Design By- Praveen Kumar-Email ID- acadone.edu@gmail.com Note- All Model is a Basic Model But Our Workshop Make a Fully Define Model..... if You interested our model then Contact me by Mail.... We Provide SolidWorks, Auto-CAD,(Mechanical Drawing 3D Design,Catia V5......etc Software Free Tutorials. You can subscribe our channel to get more information. Solidworks Easy Design Channel: Tutorials for SolidWorks on many levels and subjects Covering most of the SolidWorks fields - SolidWorks Features - SolidWorks for Beginners - SolidWorks Advanced - SolidWorks Simulation - Art & Design - etc
SOLIDWORKS sheet metal solidworks

How to draw tangent arcs between two circles in AutoCAD?

Karajko CAD
in Drafting
22 4 Beginner
In this tutorial I am going to show you the easiest way to draw arc between two circles when you need specific radius.
AutoCAD drafting radius arcs autocad

How to insert a picture in SOLIDWORKS?

Karajko CAD
in Drafting
21 3 Beginner
How to insert a picture in SOLIDWORKS?
SOLIDWORKS picture sketch solidworks

Tutorial: How to make block template DIN 6771 for AutoCad

Milan Ilić
in Drafting
20 0 Beginner
template DIN 6771
AutoCAD a0 a1 a2 a3 a4 din6771 din templates autocad

Learn Step by Step How to do Flow Simulation in SolidWorks on Cross Flow Turbine

Usman Akhtar
in CFD
18 0 Beginner
In this solidworks flow simulation tutorial you will learn how to do flow simulation on a hydro turbine, in this video I am going to do external flow simulation.
simulation flow solidworks

How to create a block in AutoCAD?

Karajko CAD
in Drafting
18 5 Beginner
In my first tutorial on GrabCAD I will show you how to create Blocks in AutoCAD. It is nothing complicated so lets start.
AutoCAD blocks autocad

Basic Command List AutoCAD

Mohit
in Drafting
17 2 Beginner
Command List AutoCAD ~ Shortcuts
AutoCAD allversion design drafting autocad

Clamp Design

Anup Chauhan
in Drafting
17 1 Beginner
Clamp Design https://www.instagram.com/p/CqAkr5bKxDZ/
NX Unigraphics assembly modeling drafting drawing clamp siemens nx nx nx cad

How to design Complete Robot using Voice Assistant like JARVIS in Fusion 360

Rugved Chavan
in Process
17 1 Intermediate
4-wheeled Robot Design Frame is 3D printable. Components - 1. Raspberry pi 4 2. Sony WebCam 3. Normal 3.5 mm jack Speaker 4. Custom Frame 5. MI 20000 mAh powerbank 6. 100 RPM Dual Shaft BO Motor - Straight with wheels Custom Voice Assistance code is running in background. Voice assistance code is connected with database which is having values like quantity and dimensions of components. Mail me for Jarvis source code. Like this video... 🤘
Fusion 360 automation electronics robots arduino engineering technology robot robotics

CFD

Vatan Gedam
in CFD
17 0 Expert
Here we are find the forces as well as pressure exerted on fan blade at the wind speed of 60kmph by using of ANSYS
flow blade pressure testing simulation wind ansys fan cfd

2. Solving 2D Problems

Ananth Narayan
in CFD
16 0 Beginner
In this tutorial we will discuss about the 2D problems which involve defining boundary condition and solving them. Iam going to create the nozzle with the air velocity inlet (ideal) and pressure outlet. Improving mesh obtain good result.
san fluent cfd ansys

Keyshot Animation Tutorial Using Simple Model Of High Bypass Turbojet Engine

Anuj Kaushal
in Process Simulation
15 2 Beginner
In this tutorial i have used keyshot software for animation purpose. I have used a 3D model of a High Bypass Turbojet Engine for denomsration. It took couple of hours to create the animation video that's why i have skipped that part from the video.
blades compressor jet turbine turbojet engine bypass high tutorial animation keyshot
White Stratasys Logo White GrabCAD Logo
© 2025 Stratasys Inc.
ABOUT US
RESOURCES
Support
SOCIAL
Streamline Pro
Control
Print
Pro
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.