Tutorials

  • Drafting ×
  • Process Simulation ×
  • Process ×
  • Standards ×

Cap screws and machine screws

dea
in Drafting
69 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.
Autodesk Inventor screw cap

I Built a Military Robot

Engineering Juice
in Process
46 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

Solidworks Tutorial # 236 How to Design a Industrials Bin in Sheet Metal by SW Easy Design

Praveen Kumar
in Drafting
24 0 Intermediate
M.K. Engineering Workshop GST : 09BETPM3972F1ZW Please any Manufacturing requirement in Rice Mill, Floor Mill, Dall Mill, any Related Product. Design By- Praveen Kumar-Email ID- acadone.edu@gmail.com Note- All Model is a Basic Model But Our Workshop Make a Fully Define Model..... if You interested our model then Contact me by Mail.... We Provide SolidWorks, Auto-CAD,(Mechanical Drawing 3D Design,Catia V5......etc Software Free Tutorials. You can subscribe our channel to get more information. Solidworks Easy Design Channel: Tutorials for SolidWorks on many levels and subjects Covering most of the SolidWorks fields - SolidWorks Features - SolidWorks for Beginners - SolidWorks Advanced - SolidWorks Simulation - Art & Design - etc
SOLIDWORKS sheet metal solidworks

How to design Complete Robot using Voice Assistant like JARVIS in Fusion 360

Rugved Chavan
in Process
17 1 Intermediate
4-wheeled Robot Design Frame is 3D printable. Components - 1. Raspberry pi 4 2. Sony WebCam 3. Normal 3.5 mm jack Speaker 4. Custom Frame 5. MI 20000 mAh powerbank 6. 100 RPM Dual Shaft BO Motor - Straight with wheels Custom Voice Assistance code is running in background. Voice assistance code is connected with database which is having values like quantity and dimensions of components. Mail me for Jarvis source code. Like this video... 🤘
Fusion 360 automation electronics robots arduino engineering technology robot robotics

Convert image to DXF in 5 minutes

Ali Nasser
in Drafting
13 2 Intermediate
Convert image to DXF in 5 minutes Jpg to DXF PNG to DXF SVG to DXF BMP to DXF PDF to DXF PSD to DXF Laser DXF Plasma DXF Waterjet DXF Adobe Illustrator DXF Autocad DXF Sheet metal DXF
AutoCAD plasma laser psd bmp png svg jpg dxf image convert

(VIDEO) NX CAD Drafting Tutorials

Diyanshu Singh
in Drafting
11 0 Intermediate
Learn basic drafting NXCAD.
NX Unigraphics drawing drafting nxcad

Tolerances in DIN 5480 splines

Carlos Soler
in Standards
11 1 Intermediate
In this tutorial, I will address some topics regarding the flank tolerances in the standard DIN 5480 splines. For an Asking of https://grabcad.com/erick.mireles-2 about the meaning of 8f in an expression like DIN 5480 W 120 x 3 x 38 x 8f
din 5480 centering tolerances fit side din 5480 spline

2D CAD EXERCISES 21 IN SOLIDWORKS

Karan Talsaniya
in Drafting
9 0 Intermediate
2D CAD EXERCISES 21 IN SOLIDWORKS Wrench Design
SOLIDWORKS wrench design solidworks 2d cad exercises 21

How to change origin of view in Catia drafting?

özgür kesebir
in Drafting
9 2 Intermediate
How to change origin of view in Catia drafting? It will show you how to change origin and axis lines in drawing.
CATIA drafting origin v5r19 catia

solidworks calculation - power and torque

taufik .
in Process Simulation
9 2 Intermediate
solidworks motion
tutorials solidworks

Static Structural Analysis

An Engineer
in Process
9 3 Intermediate
The static analysis aims to analyze the stress results, deformation results, shear-moment diagram, and reaction force results. in this tutorial, you will learn how to do static analyses for assembled models. It's an excellent tutorial for beginners in Ansys workbench. Statik analizin amacı, gerilme sonuçlarını, deformasyon sonuçlarını kesme-moment diyagramını ve reaksiyon kuvveti sonuçlarını analiz etmektir. Bu eğitimde, montajı yapılmış bir parça için statik analizin nasıl yapıldığını öğreneceksiniz. Ansys tezgahında yeni başlayanlar için çok iyi bir eğitim.
ansys static structural analysis simulation

Creating Custom Weldment Profiles in SolidWorks

Praveen Kumar
in Drafting
9 0 Intermediate
M.K. Engineering Workshop GST : 09BETPM3972F1ZW Please any Manufacturing requirement in Rice Mill, Floor Mill, Dall Mill, any Related Product. Design By- Praveen Kumar-Email ID- acadone.edu@gmail.com Note- All Model is a Basic Model But Our Workshop Make a Fully Define Model..... if You interested our model then Contact me by Mail....
SOLIDWORKS mechanical engineering sheet metal weldments solidworks

Designing Axial Static O-ring Grooves to "Industry Standards"

Thomas Larson
in Standards
9 4 Intermediate
This Covers 2/3 of everything I know about designing O-ring seals. I frequently used these while designing production tools. Most the design is based on the standards that are put forth by SAE. Personally, I be going over the reiteration by Parker since it's what I learned. Other references include the Apple Rubble Product and Trelleborg for their proprietary O-ring Gland Calculators, and the help they gave me in building my own. Links to their websites are found in Section 5. All design in this lesson is for "Static Axial Design under normal conditions”. Disclaimer: while I have completed a BS in Mechanical Engineering and have passed the FE, I am not a PE. While these calculations are standard, published, and I personally have used these practices to design multiple high-pressure tools, I cannot guarantee that they a perfect. If you are in doubt, in a hazardous environment, or using in an application that could cause harm to life, I would suggest double checking with other sources (engineering) and/or extensive testing. Also, my experience is in Oil and gas, in the continental USA. You may notice my practices being bias to API standards and in English Units, I suggest you take all I say with a grain of salt. Lesson Plan: Step 1: Background and Definitions Step 2: Finding a Published O-ring Gland and incorporating it into a design. Step 3: Designing Custom Groove using the Standards Step 4: Other Design Recommendations and Drafting Example Step 5: References and Useful links A copy of the files can be found at: https://grabcad.com/library/how-to-design-an-o-ring-gland-to-industry-standards-parts-and-photos-1
seals components calculators cals design o-rings pressure

Convert Navisworks file to STEP. file?

Tibor
in Process
8 0 Intermediate
https://grabcad.com/library/navisworks-file-nwd-to-step-1 Follow easy steps to get STEP. file from NWD. file.
convert navisworks step export

Helical gear calculation and manufacturing

Rodolfo López
in Process
7 0 Intermediate
Obtaining data from a sample helical gear. Calculation for the manufacture of helical gear
fabricacion calculo gear helical
White Stratasys Logo White GrabCAD Logo
© 2025 Stratasys Inc.
ABOUT US
RESOURCES
Support
SOCIAL
Streamline Pro
Control
Print
Pro
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.