Tutorials

  • Autodesk Inventor ×
  • BlenderCAD ×
  • NX Unigraphics ×

NX 11:Creating Assembly

Anand Panchal
in Assemblies
14 2 Beginner
A tutorial on Sub assembly and showing arrangements of hydraulic cylinder-piston assembly.
NX Unigraphics sub-assembly cylinder hydraulic arrangements assembly unigraphics nx

Mold Design in NX 10

gcom
in Design & CAD
14 3 Intermediate
Mold Design in NX 10. Without Mold Wizard and fully parametric.
NX Unigraphics tutorial 10 nx

Mold Wizard Siemens NX CAD Tutorial

Shuvam Kumar
in Modeling
14 0 Intermediate
How To Use Mold Wizard in Siemens NX CAD
NX Unigraphics cad extraction cavity core tutorial 12 wizard nx design mold

DRONE DESIGN in SIEMENS NX

MANIKANTHA P
in Modeling
14 0 Beginner
An unmanned aerial vehicle (UAV) (or uncrewed aerial vehicle,[2] commonly known as a drone) is an aircraft without a human pilot on board. UAVs are a component of an unmanned aircraft system (UAS); which include a UAV, a ground-based controller, and a system of communications between the two.[3] The flight of UAVs may operate with various degrees of autonomy: either under remote control by a human operator or autonomously by onboard computers[4] referred to as an autopilot.
NX Unigraphics siemens nx unigraphics drone

(VIDEO TUTORIAL) LAMBORGHINI ENGINE Design in UNIGRAPHICS

MANIKANTHA P
in Assemblies
13 1 Expert
The Lamborghini V12 refers to the flagship V12 engine used by Lamborghini. Lamborghini has had two generations of V12 engines through their history, both of which were developed in-house. The first-generation Lamborghini V12 was a sixty degree (60°) V12 petrol engine designed by Lamborghini,[1][2] and was the first internal combustion engine ever produced by the firm.
NX Unigraphics animation assembly v12 lamborghini engine

How to create NPT (national pipe taper) threads using inventor

engineer
in Modeling
13 3 Intermediate
I have had people ask me on here how I model npt threads for some of the parts I make, so I figured I would put it out there for others to see as well. Note: if you look at the threaded models I have on this website you will see that I have clearly taken more time on some of them than others, this tutorial will teach you how to do it the right and proper way.
Autodesk Inventor threads npt

Simple modeling routine demonstration #1

José Luiz Soares
in Modeling
13 1 Beginner
Simple modeling routine demonstration #1 Hinge
Autodesk Inventor inventor steel hinge modeling

Part View Labels with BOM item number

PRO
in BOM
13 2 Intermediate
Set Your Drawing View Labels to Use BOM item numbers.
Autodesk Inventor parametric parame part number item label view bom

How to model a truncated icosahedron with Autodesk Inventor

Jens Nielsen
in Modeling
13 4 Intermediate
Mix 2D- and 3D sketches to create this platonic body.
Autodesk Inventor

Basic Modelling 1 (NX Unigraphics)

Bhargava Krishna Marripati
in Modeling
13 0 Beginner
Basic modelling techniques using NX Unigraphics.
NX Unigraphics modelling nx

Centrifugal Pump

Arvin Kareem
in Modeling
13 0 Beginner
Arvin Kareem - Kelompok 1 Vismod 3
Autodesk Inventor

Modelling of Piping Part

Mohit
in Design & CAD
12 0 Beginner
Use for connecting two pipe at rectangle.
Autodesk Inventor pipe model inventor

IMPELLER IN AUTODESK INVETOR | AUTODESK INVENTOR TUTORIAL | 3D MODELING

ROHAN GUPTA
in Modeling
12 1 Beginner
INVENTOR
Autodesk Inventor

How to create Rack & Pinion using Inventor 2016

Ebrahim Abu Has
in Modeling
12 0 Intermediate
How to create Rack & Pinion with Inventor 2016 and show the motion??? Step by Step tutorial .... follow the link below https://www.youtube.com/playlist?list=PLCrNndUdp-R2RXvptMFVptVGuLDD0NV2f
Autodesk Inventor constrains drive assembly modelling 3d 2016 inventor pinion rack

Inventor 2021 | Radial Engine | Assembly 9

CAD Pond
in Assemblies
11 3 Beginner
In this video, I demonstrated the assembly of the cylinders and pistons with the crank case used in a typical radial engine. Video demonstrations to the parts used, can be found on my youtube channel linked in my profile. Happy Modeling!
Autodesk Inventor airbus inventor engine radial aviation boeing airforce aircraft
White Stratasys Logo White GrabCAD Logo
© 2025 Stratasys Inc.
ABOUT US
RESOURCES
Support
SOCIAL
Streamline Pro
Control
Print
Pro
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.