Tutorials

Square drill hole Bit design in solidworks

22 6 Intermediate
Please support on paypal so this channel can create more better content: paypal.me/nobodyknow137 In this video i am going to tell you how to make square drill hole bit design in solidworks this is very useful in carpentry where square drill hole required frequently . i have shown all the process how to make the part and deeply explained i hope you guys will like it. It is a very good project for mechanical engineers

Create a Simple Nut By Using PTC Creo Parametric 3.0

14 3 Intermediate
How to create a simple nut in PTC Creo Parametric 3.0 ???

Modelling Plastic Cover in CATIA V5

12 4 Beginner
In this tutorial, we will first create a shaft feature with thickness, in CATIA V5 using opened sketch. Then, we will apply a circular profile pad using 2 limits and add a concentric hole to it. Later, we will add a stiffener between the pad and the shaft created, and apply edge fillet all around it. Lastly, we will create a circular profile pocket and apply circular pattern around the shaft axis.

Filling basic 6-sided holes in Rhino

8 1 Beginner
This tutorial shows how to fill a 6-sided hole surrounded by simple planar surface transitions in Rhino.

SolidWorks Advanced 3D Part Modeling Tutorial

8 0 Intermediate
In this video, we are going to create a 3d Model from 2D Drawing. Rib, Boundary Boss, Loft Cut, Symmetric pattern, Hole Wizard are the command that are used in this video. I hope it will escalate your 3d modeling skills.

CATIA V5 - 2D into 3D Modeling - Exercise

8 4 Beginner
In this guide are displayed CATIA V5 steps modeling based on technical drawings 2D into 3D modeling. With especially attention take a look the introduction of the new body which multiply holes, when the standard methods can not be used (mirrors, circular patterns ...).

Single Inspection Dimension for Holes

6 1 Beginner
I was having a hard time figuring out a good way to dimension a hole with both the diameter and depth of a hole with GD&T in a singe dimension. This dimension also required inspection so I wanted the inspection circle around the dimension and have the properties linked to the model. I did a lot of searching on the internet and did not find a good solution. Here is my solution. please leave your comments if you have a better way to do this.

SOLIDWORKS - Exercise: 2D into 3D Modeling - Part design training -

6 0 Beginner
Please, look, how it looks this 2d drawing in 3D as a body, watching this video. https://youtu.be/Q8wlGo8aJUo Thanks.

2D into 3D Modeling - Part design training - SOLIDWORKS - Exercise

4 2 Beginner
Look how it looks this 2d drawing in 3D as a body !

SolidWorks - Exercise - 2D into 3D Modeling - Extrude - Shall - Hole with thread - Fillet

4 0 Beginner
In this guide are displayed SolidWorks steps modeling based on technical drawings 2D into 3D modeling. The 2D drawing is pump cover. Example of exercise/Part Design training. Basic features: Boss-Extrude, Shell, Mirror, Hole, Hole with thread, Circular Pattern, Rectangular Pattern, Fillet. Basic entities of the sketches: Line, Circle, Rectangle Fillet. Reference elements: Offset plane.

Make a shower drain with Flanged Hole

3 0 Beginner
https://youtu.be/gyzdFPjSGXc Here is a demonstration showing you the design of a shower drain grid in CATIA 3DExperience. The Sheet Metal Design application, based on industry process features, allows you to create quickly a plate that you can bend and add stamp, dowel, bridges, etc. This video is divided in two parts. First you see how to design the outer plate (using walls, flange and corner relief). The second part deals about the grid's design. In this Part, you will use GSD to create a repetition of points that will allows you to pattern the Flanged Hole Feature.

(Video) SolidWorks Drafting Tutorial: Countersinks | Hole | Angle Bracket| Practice for Beginner | Tech Hawk

3 0 Beginner
In this tutorial, Tech Hawk is going to show you how to do a model of Angle Bracket. I've also showed you how to make Countersinks in a part. It will help beginners to practice different features of SolidWorks.

2D into 3D Modeling - Part design training - Autodesk INVENTOR - Exercise

3 2 Beginner
Look how it looks this 2d drawing in 3D as a body !

How does the hole wizard work?

3 0 Beginner
Here's a brief write-up/rant.

Filling 6-sided holes in Rhino

3 0 Intermediate
This tutorial shows how to fill a 6-sided hole surrounded by complex surface transitions in Rhino.